Opens in a new tab
EST. 2007
ADMISSIONS OPEN
Apply Now
← Creative Hut Library
Shutter speed · Light trails

Light Trail Photography: Settings, Location and Timing

10 min read10 questions

By Abin Alex and Anu Joseph

Creative Hut Academy Library · Updated 13 November 2026

Abstract

A guide to light trails, the lines that moving lights draw during a long exposure. It covers the starting settings, where to stand and stay safe, how the exposure length changes the trails, when to shoot, how to use Bulb for long exposures and how to add people with flash. Every point gives camera steps in Manual.

Keywords: light trail photography, light trails settings, long exposure traffic, car light trails, night long exposure, Bulb mode

01 · Light trails

What are light trails?

Short answer. Lines drawn by moving lights, such as car lamps, during a long exposure, while still things stay sharp.

Definition

Light trails are lines drawn by moving lights during a long exposure. Car headlamps and tail lamps, buses, trains and fairground rides become streaks of light while buildings and roads stay sharp.

Key facts

  • A long exposure uses a slow shutter, from about half a second to many seconds, so movement builds up over time; 30 s gives light trails.
  • Headlamps make white trails and tail lamps red ones, so the side of the road you face sets the colour.
  • Fairgrounds, fireworks, street lights and moving traffic make good subjects for long exposures (Langford and Andrews, 2009).
  • The camera must stay still, so a tripod is essential.
How to

Manual (M), on a tripod

  1. Fix the camera on a tripod and turn stabilisation off.
  2. Set M, ISO 100 and f/8.
  3. Set 15 s and start with the 2 second timer.
  4. Check the trails and the brightness, then adjust the time.
Cham tip

Face the traffic for white trails, its back for red.

Cham task
  1. Photograph one road facing the oncoming traffic.
  2. Photograph it again facing the traffic moving away.
  3. Compare the colour of the trails.
Quiz
In photography

Photograph a bus stand at night with buses leaving.

In cinematography

Music videos use the same streaked lights for a sense of speed and city energy.

End of 01 · Light trailsNext: 02 · Settings
02 · Settings

What settings should I use for light trails?

Short answer. ISO 100, f/8 and 10 to 30 seconds on a tripod, in Manual.

Definition

Light trail settings keep the shutter open long enough for the lights to cross the frame while the rest of the scene stays correctly exposed. A low ISO and a middle aperture allow the long time.

Key facts

  • A starting point for car light trails is 10 to 30 s at f/8 and the lowest ISO.
  • A guide exposure for light trails is about 10 s at f/8 at ISO 100 (Cope, 2006, p. 55).
  • Use a low ISO and a small aperture so a long exposure does not overexpose (Langford and Andrews, 2009).
  • A digital camera needs no reciprocity correction, but long exposure noise reduction doubles the waiting time.
How to

Manual (M)

  1. Set M, ISO 100 and f/8.
  2. Set 10 s and take a test frame.
  3. If the trails are too short, lengthen the time and close the aperture one stop for each doubling.
  4. Shoot RAW with Tungsten or about 3200 K white balance to calm the orange street light.
Cham tip

Count stops: double the time, close one stop.

Cham task
  1. Shoot one scene at 10 s f/8, 20 s f/11 and 40 s f/16.
  2. Check that the buildings stay the same brightness.
  3. Compare the trail length.
Quiz
In photography

Make a settings card for 10, 20 and 30 s trails and test it on one road.

In cinematography

Cinematographers get a similar look by shooting at a low frame rate and long shutter, then playing it at normal speed.

End of 02 · SettingsNext: 03 · Where to stand
03 · Where to stand

Where should I stand to photograph light trails safely?

Short answer. On a footbridge or a raised, safe spot with a view along the road, with the tripod on firm ground, never in the traffic.

Definition

The place you stand sets the shape of the trails and your safety. A footbridge or a raised spot looks along the road, and a bend or junction makes the trails curve.

Key facts

  • Stand on a pedestrian bridge over a busy road with the camera on a tripod, but avoid clamping it to the bridge, which vibrates (Cope, 2006, p. 54).
  • Bends, roundabouts and junctions make curved trails that lead the eye.
  • Never stand in the road or on a narrow verge; traffic drivers cannot see you.
  • Wear something bright and keep your bag behind you, not on the footpath.
How to

Setting up

  1. Choose a footbridge or raised spot with a view along a bend.
  2. Spread the tripod legs wide on firm ground, away from the railing.
  3. Frame the road with a building or landmark for place.
  4. Set M, ISO 100, f/8 and 15 s and test.
Cham tip

Safety first. No picture is worth standing in traffic.

Cham task
  1. Find a footbridge or raised spot over a road bend in your town.
  2. Visit in daylight to check safety and the view.
  3. Return at dusk to shoot.
Quiz
In photography

Map three safe trail spots in your town with notes on the view.

In cinematography

Film crews close or control roads with police permission before filming traffic scenes.

End of 03 · Where to standNext: 04 · Timing and length
04 · Timing and length

How do timing and exposure length change the trails?

Short answer. Short exposures show separate moving lights; long ones draw continuous lines that trace the road. Shoot at dusk for a coloured sky.

Definition

The exposure length decides how the trails look. Shorter times show separate streaks of moving lights against a dark road, and longer times draw continuous lines that trace the shape of the road.

Key facts

  • Shorter exposures show the motion of the vehicles against a dark background; longer exposures draw the lights into lines that define the shape of the road (Cope, 2006, p. 54).
  • Longer exposures also light the surroundings through the combined street and traffic light (Cope, 2006, p. 54).
  • Start the exposure just before the traffic arrives, so the trail runs through the whole frame.
  • At dusk the sky still holds colour, so trails at dusk often look better than at full night.
How to

Manual (M)

  1. Set M, ISO 100 and f/8 on a tripod.
  2. Shoot 5 s, 15 s and 30 s as traffic passes.
  3. Start each frame just before a group of vehicles enters the frame.
  4. Pick the length that fills the road with lines.
Cham tip

Start before the traffic. End after it leaves.

Cham task
  1. Shoot the same road at 5, 15 and 30 s.
  2. Shoot the best length again at dusk and an hour later.
  3. Compare the sky in both.
Quiz
In photography

Make a set of three trail pictures of one road at dusk, at night and after rain.

In cinematography

Editors cut light-trail shots into city montages to show the pace of a place.

End of 04 · Timing and lengthNext: 05 · Bulb
05 · Bulb

How do I use Bulb mode for very long light trails?

Short answer. For times longer than 30 seconds, use Bulb with a lockable remote and count the seconds.

Definition

Bulb keeps the shutter open as long as you hold the button, for exposures longer than the camera timed speeds. A lockable remote holds it open without touching the camera.

Key facts

  • Longer than 30 s needs Bulb, which keeps the shutter open while you hold the button. Use a remote release.
  • Canon: turn the mode dial to B. Nikon and Sony: in M, turn the shutter dial past 30 seconds to Bulb.
  • Close the aperture or use an ND filter so a very long time does not overexpose the scene.
  • Long exposure noise reduction doubles the waiting time.
How to

Bulb (B)

  1. Set B (Canon) or turn the shutter past 30 s in M (Nikon, Sony).
  2. Set ISO 100 and f/11.
  3. Lock the remote open and count the seconds, such as 60.
  4. Release, wait for noise reduction and check the picture.
Cham tip

Lock the remote. Do not hold it with a shaking hand.

Cham task
  1. Shoot a 60 s Bulb exposure of a busy road at f/11.
  2. Shoot 120 s at f/16.
  3. Compare the trails and the brightness.
Quiz
In photography

Time a 60 second exposure with a clock instead of guessing.

In cinematography

Some film cameras run at very low frame rates to record light movement for time-lapse shots.

06 · People and flash

How do I add people to light trail pictures?

Short answer. Use flash with rear curtain sync: the long exposure records the trails and the flash freezes the person at the end.

Definition

Adding people to light trails means freezing the person while the lights still streak. A flash with rear curtain sync fires at the end of the long exposure, so the person is sharp and the trails fall behind any movement.

Key facts

  • Rear, or second, curtain sync fires the flash at the end of the exposure, so light trails of a moving subject stay behind it.
  • With flash, a longer exposure such as 1/15 s or 1/8 s records more of the scene by its own light (Cope, 2006, p. 68).
  • For a still person against traffic trails, use a tripod, ask them to stay very still and fire the flash at the end.
  • Keep the person safely off the road, on a footpath or bridge.
How to

Manual (M) with flash

  1. Fix the camera on a tripod and set M, ISO 200, f/8 and 4 s.
  2. Turn on the flash with rear curtain sync.
  3. Ask the person to stand still until the flash fires.
  4. Lengthen the time for longer trails behind them.
Cham tip

The flash freezes the person. The time draws the trails.

Cham task
  1. Photograph a friend on a footbridge with traffic trails behind at 4 s and rear curtain flash.
  2. Repeat at 10 s.
  3. Compare the trails and the sharpness of the person.
Quiz
In photography

Make a portrait of a friend with festival lights streaking behind using rear curtain flash.

In cinematography

Music video directors use the same mix of flash and long exposure for dreamlike stills.

End of 06 · People and flashNext: Questions beginners ask

Questions beginners ask

What are the best settings for light trails?

On a tripod, set Manual, ISO 100, f/8 and 10 to 30 seconds, and start the exposure just before traffic arrives.

Do I need a tripod for light trails?

Yes. The camera must stay still for seconds; a wall can work in an emergency, but a tripod is far better.

Why are my light trails too bright?

The time is too long for the aperture. Close to f/11 or f/16, lower the ISO to 100, or use an ND filter.

Can I shoot light trails with a phone?

Some phones have a long exposure or light trail mode. Rest the phone on something steady.

References

  • Cope, P. (2006) Night and low-light techniques for digital photography. Buffalo, NY: Amherst Media.
  • Langford, M. and Andrews, P. (2009) Langford’s starting photography: The guide to creating great images. 6th edn. Oxford: Focal Press.

Read next in the Library

How to cite this guide. Alex, A., & Joseph, A. (2026). Light trail photography: A guide for photographers and cinematographers. Creative Hut Academy. https://creativehut.org/library/light-trail-photography/

© 2026 Creative Hut Academy. Written by Abin Alex and Anu Joseph. Drafted with AI assistance. Last updated 13 November 2026. To copy, republish, translate or adapt any part of it, including the diagrams, you need written permission. Ask through the contact page. The books, standards and data sheets listed above are sources, not copies. Found a mistake? Write to director@creativehut.org.
More guides in the Library →
Learn this hands on

Make this your craft at Creative Hut Academy

Creative Hut Academy in Mattakkara, Kottayam, Keralam teaches photography, cinematography, editing, sound and AI filmmaking in one-year residential diplomas. Students come from across India.

Want to talk? Message us on WhatsApp, or ask Cham, our AI mentor, a study doubt.